Seattle neighborhoods
Laurelhurst: Five Mistakes I Undo
Crest & Level works throughout Laurelhurst, on the peninsula's Tudor, Colonial Revival and mid-century houses, including lakeside and view lots.
Laurelhurst started as a mill town. In 1888, Henry Yesler and an investor platted the Town of Yesler around a sawmill on Union Bay, where Union Bay Place runs today. Between 1906 and 1909, the McLaughlin Realty Company turned the peninsula into a planned residential district, with utilities in place and the golf club persuaded to move elsewhere. The area joined Seattle in 1910. What followed was decades of substantial houses on generous lots, many with lake or mountain views.
Good houses attract a lot of remodeling, and not all of it ages well. Much of the work in Laurelhurst is fixing earlier jobs that looked fine when they were finished. Here are the top five.
Quick answer: Crest & Level handles finish carpentry, trim and millwork matching, wood window and door repair, tile and shower rebuilds, interior painting, deck repair and aging in place modifications for Laurelhurst homes. We correct earlier remodels that didn't hold up, work carefully on view and lakeside lots, and source locally from Tweedy & Popp in the U District, Dunn Lumber, Limback Lumber and O.B. Williams.
Mistake 1: Replacement windows that don't fit the house
A Tudor or Colonial Revival house with its original windows swapped for flat vinyl units loses much of its character. The new frames are often wider and flatter, the divided lights disappear or become fake grilles, and the old casings get trimmed back to fit. The windows can also leak at the perimeter if they were caulked in place without a sill pan or proper flashing.
What I do instead: I restore original wood windows where they're sound. Where replacement is the right call, I use units sized and detailed for the opening, with true or simulated divided lights where the style calls for them. Each one goes in over a sill pan with shingle-lapped flashing, and the casings are rebuilt to match the profiles. See Doors & Windows.
Mistake 2: Showers rebuilt without real waterproofing
The tile looks great for five years. Then the grout keeps cracking, the floor next to the tub goes soft, and a stain shows up on the ceiling below. In most cases the shower was built without a continuous waterproofing membrane, or with plastic sheeting behind a membrane so the wall can't dry in either direction.
What I do instead: I rebuild with one waterproofing layer in the right place: a bonded sheet or liquid membrane running unbroken from the drain up the walls, with flexible sealant at every change of plane, and a bath fan ducted outdoors. See Kitchen & Bath.
Mistake 3: Original trim replaced with stock moldings
In many Laurelhurst houses, a remodel replaced part of the original trim, such as one room, one doorway or a new addition, with whatever profile the lumberyard had in stock. The seam shows every time you walk through.
What I do instead: I match the original profile. A sample goes to O.B. Williams or Limback Lumber, and when nobody stocks the profile anymore they can grind new knives to reproduce it. The new trim is installed with coped inside corners so the joints stay tight through Seattle's wet and dry seasons. See Cabinetry and Finish Carpentry.
Mistake 4: View decks attached without flashing
On a view lot, the deck is often the most-used room in the house. When a deck ledger is bolted against the siding without flashing, water runs down the wall, gets trapped behind the ledger and rots the ledger and the house's rim joist together. That's the most serious rot point on an attached deck, because it's structural.
What I do instead: I flash the ledger to the house, with the flashing lapped under the siding or housewrap. I use the right fasteners into the rim joist, keep the posts off the concrete, and build guards at code height that keep the view open. See Fencing & Decks.
Mistake 5: Doors planed until they don't fit
An original door that sticks in winter gets planed down. In August it rattles, the latch misses the strike and the weatherstripping can't close the gap. Usually the door wasn't the problem. The house had moved and the jamb was out of square.
What I do instead: I fix the frame first. I re-shim the jamb and reset the hinges with long screws into the framing to bring the reveal back even, then seal all six faces of the door so it stops taking on moisture. Planing comes last and only if it's still needed.
At the water's edge
Lakefront and near-shore lots in Laurelhurst come with an extra layer of rules. Seattle's shoreline regulations generally apply to work within 200 feet of the shoreline. New structures, decks, bulkheads and changes to the ground near the water can need shoreline review on top of a building permit. Interior repairs and like-for-like maintenance usually don't. When your work is near the water, I'll tell you up front whether it's likely to need review, and we can check with the City before planning anything.
Lakeside houses also take more weather. Wind off the lake drives rain into the sides that face the water, so window sills, door thresholds and exterior trim on those elevations get stainless fasteners, back-primed wood and careful flashing.
Where your materials come from
- Tweedy & Popp Hardware at UW, 4731 University Way NE: the closest full hardware store to most of Laurelhurst.
- Dunn Lumber – Lake Union, 3801 Latona Ave NE: finish lumber, sheet goods, and Marvin and Milgard window and door showrooms.
- O.B. Williams, SODO: custom millwork, wood windows and doors.
- Limback Lumber, Ballard: custom molding profiles.
- Fisheries Supply: marine-grade stainless hardware and sealants for exposures facing the lake.
When it's bigger than us
Bulkheads, docks, new structures near the shoreline, removing bearing walls, and engineered decks on steep slopes are work for general contractors, engineers and marine contractors. If your project is heading that way, I'll tell you early and point you to people I trust.
Staying in your Laurelhurst home
Many Laurelhurst houses are on more than one level, with long stairs, a primary bedroom upstairs and steps down to a view deck or yard. Handrails on both sides of every stair, grab bars anchored into framing, lower thresholds to the deck and better lighting usually come first. An aging in place assessment ranks the rest.
What to expect
- First visit: I walk the house with you, look at the specific problem and what's around it, and tell you plainly what I'd do and what I wouldn't.
- Estimate: A written, itemized scope, including what's likely to change once a wall or floor is opened. Why I don't rely on fixed bids.
- Scheduling: I will provide an accurate plan for scheduling and completing the work.
- Cleanup: Dust containment as needed with your house left clean every day.
Laurelhurst questions I hear most
Can you fix a remodel that used the wrong trim? Yes. A sample of the original profile can be reproduced by a Seattle millwork shop, even when it isn't stocked anymore, and the mismatched trim replaced so the house reads as one piece again.
Do I need a shoreline permit for work on my Laurelhurst lakefront house? Interior repairs and like-for-like maintenance usually don't need one. New structures, decks, bulkheads and changes to the ground within Seattle's shoreline jurisdiction, generally within 200 feet of the water, can need shoreline review. Check with the City before planning that kind of work.
Why does my deck ledger rot? Usually because it was bolted against the siding without flashing, so water running down the wall gets trapped behind it. Flashing the ledger to the house with the flashing lapped under the siding, and using the right fasteners into the rim joist, prevents it.
My door sticks in winter and rattles in summer. What's wrong? The house has likely moved and the jamb is out of square, and the door may have been planed to compensate. Re-shimming the jamb, resetting the hinges and sealing all six faces of the door usually fixes it without more planing.
Let's look at it together
I work across north Seattle, a short drive from Queen Anne. Call or text (564) 444-8388 and tell me what's going on with your Laurelhurst house, or schedule a visit.
What we do in Laurelhurst
Cabinetry and Finish Carpentry
Custom shelving, trim, and built-ins fabricated and installed to match the character of your home.
Learn more →
Doors & Windows
New doors and replacement windows installed cleanly and finished to match your existing trim and hardware, so everything looks like it was always meant to be there.
Learn more →
Kitchen & Bath Updates
We handle the upgrades that make your kitchen and bath feel new again — cabinet hardware, pullouts, light fixtures, mirrors, toilets, and tile repair and installation.
Learn more →
Fencing & Decks
New fencing and deck construction and repairs built to last in the Pacific Northwest — properly framed, cleanly finished, and designed to complement your home rather than just fill the yard.
Learn more →
Painting
Precision roll, brush, or spray painting for walls, ceilings, trim, and cabinets with a clean and lasting finish.
Learn more →
Aging in Place Modifications
We install grab bars, accessible toilets, ramps, wider doors, and updated hardware and electrical to make your home safe and comfortable.
Learn more →
Guides for Laurelhurst homeowners
Why Laurelhurst homeowners work with us
Licensed, local, and built for this neighborhood.
Licensed, bonded & insured — License #CRESTLH742JA
20+ years of carpentry and craft experience
Local to Laurelhurst, based on Queen Anne