How much does door replacement cost in Seattle?
Quick Answer
Door replacement in Seattle costs $300–$800 for interior doors and $5,000–$12,000 for exterior entry doors installed, depending on materials, glass, hardware, and the condition of the existing framing. Entry doors with sidelites run $12,000–$20,000. Older homes often need rot repair or opening adjustments that add time to the job.
Typical Costs by Door Type
| Door Type | Typical Seattle Range |
|---|---|
| Single exterior entry door (installed) | $5,000–$12,000 |
| Entry door with two sidelites | $12,000–$20,000 |
| Patio/sliding door (two-panel) | $4,000–$12,000 |
| Interior passage door | $300–$800 |
The wide range reflects material quality, glass content, hardware, and the condition of the existing framing. Labor in Seattle runs approximately $150/hour for a qualified installer. Front door replacements almost always uncover out-of-square or out-of-plumb openings — a skilled craftsman adjusts the rough opening so the door operates properly for years to come, not just on installation day.
What Drives the Cost in Seattle
Moisture and rot. The biggest variable is rot discovered when the old door comes out. Seattle's moisture attacks door jambs (especially at the threshold), the sheathing behind exterior trim, and the sill plate beneath the door. Surface rot adds a few hours of wood replacement; rot that reaches the sill plate, framing, or sheathing can turn a one-day install into a two- to three-day project. Homes over 30 years old should assume some rot repair will be needed and keep a contingency in the budget.
Non-standard openings. Pre-1980 Seattle homes often have rough openings 1–2 inches off modern standard sizes, and Craftsman and Tudor homes frequently have wider or taller doors than current stock sizes. These need a special-order door sized to the real opening, or frame modification. Installers unfamiliar with older homes quote standard pricing, then discover the extra work mid-job.
Seasonal wood movement. Constant moisture from October through May tests weatherstripping and threshold seals, while dry summers shrink wood frames. A door that works perfectly in July can stick in January. Experienced installers set reveals and adjust hardware with that seasonal movement in mind.
Weatherproofing. North-facing entries get little drying time between rain events, so flashing details matter more than the door itself. Proper installation includes:
- Flashing above the door
- Pan flashing under the threshold
- Quality weatherstripping and a door sweep
- A threshold height that sheds water
- Exterior trim detailed to drain
Choosing a Door Material
Steel — the most economical option, with foam-core insulation. Dent-resistant but can rust where the finish is scratched, and style options are limited. Lifespan 20–30 years. Best for budget projects, modern homes, and back or side entries.
Fiberglass — realistic wood grain that won't rot, warp, or rust, with excellent insulation and a wide range of styles including Craftsman. Lifespan 30–40 years. The best all-around fit for Seattle's climate and for period-style homes.
Wood — authentic appearance for historic homes, with custom options. Needs sealing every 3–5 years and can warp or rot if neglected. Lifespan 25–50+ years with proper care. Best for historic and high-end homes.
For energy efficiency, look for Energy Star certification and a U-factor of 0.30 or lower — though installation quality matters more than the door itself. The best door installed poorly performs worse than a budget door installed correctly.
Style matching: Craftsman homes suit 5-panel doors in wood or grained fiberglass; Tudor and Colonial homes suit traditional 6-panel designs; mid-century homes often use flush doors with sidelites; contemporary homes suit modern designs with glass panels. Handlesets, quality deadbolts, decorative glass, and sidelites all add to the total.
The Installation Process
Preparation: Protect interior flooring, remove the old door and trim, assess the opening, repair any rot, and verify rough opening dimensions.
Installation: Set the prehung unit, shim it plumb and level, fasten through the jamb, set even reveals, and install exterior trim with flashing and weatherproofing.
Finishing: Install interior trim, adjust the threshold, install hardware, adjust weatherstripping, and test the door through its full swing.
A straightforward same-size replacement is typically a one-day job. Rot repair, non-standard sizing, or structural work extends it to two or three days — ask how long the house will be open, since that matters for security.
Common Problems and What Causes Them
Sticking doors usually come from seasonal wood movement. A proper installation leaves seasonal clearance and should operate smoothly year-round.
Water intrusion is almost always a flashing or threshold problem. It can't be fixed with caulk alone — don't accept "we'll seal it better" as the solution.
Sagging doors come from improper shimming or too few fasteners through the jamb, and are fixed only by reinstalling with proper technique.
Lead Times
- Stock doors: same day to 1 week, limited sizes and styles
- Special-order doors: 3–6 weeks, required for non-standard sizes, worth the wait for proper fit
- Custom doors: 8–12 weeks or more, typically high-end wood doors or unusual openings
Permits
A same-size door replacement typically doesn't need a permit. Changing the door's size or location, or making structural modifications, does. Seattle permit fees for this work run roughly $200–$400 and can add 1–2 weeks. Check with Seattle DCI for your specific project.
Questions to Ask a Contractor
- "How many Seattle door installations have you completed?"
- "What's your process for dealing with rot in older homes?"
- "How do you handle weatherproofing and flashing?"
- "What's included in your price?" (hardware, trim, disposal, cleanup)
- "How do you handle unexpected rot or non-standard sizing?"
- "What's your warranty on installation?"
Be wary of contractors who quote without seeing the existing door and opening, don't mention flashing, can't explain how they handle seasonal wood movement, won't provide a written warranty, or don't ask about rot in an older home.
After Installation
Check weatherstripping seasonally during the first year, adjust the threshold if any water gets in, and lubricate hinges annually. Wood doors need sealing or staining every 3–5 years, and all doors need new weatherstripping every 5–10 years.
Need Help?
Door replacement in Seattle requires understanding of moisture management, weatherproofing, seasonal wood movement, and the rot common in older homes. Crest & Level handles entry, patio, and interior door installation, including rot repair, custom fitting for non-standard openings, and proper flashing — so your door operates smoothly through every season. Contact us for a no-pressure assessment of your specific situation.
Related questions
- How much does window replacement cost in Seattle, and what affects it?
- How do I hire a window or door contractor in Seattle?
- How do I find a licensed contractor for small home repairs in Seattle?
- Which pre-listing repairs increase home value in Seattle?
See our Doors & Windows services.
Get started
Ready to get started?
Reach out for an estimate. We'll talk through the scope and get back to you within 72 hours.